kezdőlap > műsorlista
Zirconia milling beads are used to grind metals and other materials. Their key advantage is their capacity to grind through a range of media, such as stainless steel or ceramics, without harming the material. The downside of these products is their high cost. If you're looking for new grinding media, consider alumina or silicon carbide.
Zirconia grinding medium, often known as YTZ, is a metallic combination of zirconium oxide and yttrium oxide. They are very spherical and have a tremendous energy impact. When compared to other materials, YTZ has the maximum density of 6050 kg m-3, making it the ideal media for wet grinding processes at high speeds. YTZ can be utilized in the milling of lithium iron phosphate in general.
Furthermore, it has a lengthy lifespan. Unlike other grinding media, YTZ does not require frequent replacement. As a result, the total operating cost of this material is relatively cheap. This is primarily owing to the refractory character of YTZ. The ceramics used in YTZ have a high hardness and exceptional wear resistance.
Aside from the apparent usage of YTZ, there are various ways to make the most of it. A suitable solvent, for example, can assist in lowering the mass specific comminution energy. Another technique to improve the effects of YTZ is to combine it with the proper size grinding media.
As grinding media, a number of ceramic materials are employed. Silicon nitride, aluminum oxide, tungsten carbide, and zirconium silicate are among them. To select the best grinding media, evaluate its qualities as well as its application. For example, you should determine the material's hardness and whether it can be used in your specific equipment. Furthermore, you should be aware of the media's size as well as the container in which it will be employed.
When selecting a material for grinding, consider its hardness, as this can affect its wear resistance. Some processes necessitate the use of softer material with a higher alumina content. This may result in a higher-quality product. Another factor to consider is the cost of switching media. The fewer modifications you make, the lower your long-term costs will be.
Yttria-stabilized zirconia ceramics are becoming increasingly used in a variety of applications. They are ideal for a variety of applications, such as high-density, ultrafine grinding, and re-circulation operations. Their density and strength are particularly noteworthy.
A precise particle size distribution is required for making cirkónium-dioxid marógyöngyök. The particle diameter should be smaller than 8 mm. A submerged granulation process combining water and alcohol has been proposed to create zirconia microbeads with tiny average particle diameter.
In addition to the submerged granulation process, the direct powder rolling method can be used to prepare microcrystalline zirconia. The particles are rolled using a revolving ball machine in this process. It has the ability to produce uniform and high bulk density. A titration approach, on the other hand, can be utilized to create fine zirconia beads.
The slurry of oxide particles is prepared using this procedure. The zirconia medium is applied in a proportion of 0.1 to 1.0 parts by mass to 100 parts by mass. Slurry concentration should be between 5 and 30%, depending on the desired particle size range. Before dropping the slurry into a CaCl2 solution, zirconia particles are covered with a gelled coating.
The fine average particle diameter of zirconia beads is suitable for a range of applications. Nanotech materials can be dispersed using these microbeads. They also have a high compressive strength. As a result, they are appropriate for grinding high-performance materials.
Média nedves malomgép can be a useful approach for producing nanosuspensions of poorly water-soluble therapeutic candidates. Many weakly water-soluble medications, on the other hand, are difficult to synthesize and may have unwanted side effects.
The ideal particle size for wet media milling is determined by the drug's mechanical characteristics. As a result, the bead size must be carefully considered. The size of the bead should ideally be proportional to the drug's hydrophobicity.
The vibratory milling of a poorly water-soluble chemical was investigated in order to obtain an optimal method. The milling of nanoparticles was effectively accomplished using an acoustic mixing equipment. The milling process was accelerated by sequentially increasing particle size.
Wet media milling is a well-known formulation method. Its benefits include low excipients, low energy usage, and little media wear contamination. However, there are drawbacks to wet media milling, such as long cycle times and significant energy usage.
Tencan's manufacturing plant for nedves gyöngymarás covers 20,000 square meters, while its R&D center covers 22,000 square meters. This means that Tencan can meet the needs of all consumers. Tencan has worked with 20 physicians from five prestigious universities and has received over 30 patents.
The primary focus of the company is on three areas: powder equipment, powder technology, and powder materials. Our principal products include laboratóriumi golyósmalom, planetary ball mills, crushing and milling machines, mixing and screening equipment, and other lab equipment such as glove boxes, scientific equipment, and other items.
ISO9001, CE, SGS, and other certifications have been obtained by the company. Furthermore, it holds over 40 patent innovations that are covered by independent intellectual property rights including függőleges bolygógolyósmalom. It has been certified as a "high-tech Enterprise within the Hunan Province" by the government.
Universities, research institutes, and technology-based corporations are the primary customer groupings, with over 20,000 customers globally and exports to more than 60 countries.
EN 
NL
FR
DE
HI
IT
KO
PL
PT
RU
ES
TR
AR
BG
HR
CS
DA
FI
EL
JA
NO
RO
SV
IW
ID
LV
LT
SR
SK
SL
UK
VI
ET
HU
UZ
TH
FA
MS
BE
HY
AZ
KA
MN
MY
KK
TG
